Search
815 results found for "neon"
-
285-426047 RIG - Ball Bearing 10 x 15 x 4 (4 pieces)
$10.00
10 x 15 x 4 ball bearings for the RIG. These Large Bearings are for the Inner Wheel Bearings. Mounted in the Front Steering Hubs and the Rear Uprights. You need 4 of them. These are also for the Differentials and you need 4 of them for the Diffs. There are 8 of them on the truck.
-
285-3448 BURST AUTO ESC
$12.00
This is a replacement Electronic Speed Control for the LiteHawk BURST AUTO The ESC is the Heart and Brain of the BURST AUTO. To replace, there are 16 soldering points that must be dealt with to put a new ESC in place. The ESC Removing the ESC means de-soldering all 16 solder points...
-
-
285-481008 Steering Assembly
$4.00
Removing Steering Linkage - Follow the instructions to Remove and Replace The Baja Gear Case Cover.. only up to removing the upper chassis. Don't remove the small screw holding the Gear Case Cover on. With the upper chassis set aside you can take one of the screws and replace it into the Gear Case Spacer,...
-
-
285-3445 BURST AUTO Motors (2 front, 2 rear)
$10.00
This is a full replacement set of 4 motors for the LiteHawk BURST AUTO Make sure that you replace a damaged motor with the correct one, or it will not fly. Access the Motor, Motor housing, Landing Pads, and Carbon Fiber Arm. ...
-
-
285-428107 C-Chassis - Steering Tie-Rods
$5.00
For Litehawk NOMAD With the Front Wheels removed, follow above instructions to remove the Upper and Lower Suspension Arms from the Chassis only, and remove the screw holding the Upper shock to the Shock Tower, every thing can remain attached to the Wheel Hubs. Now remove the six screws holding the Servo, or Front Upper Chassis...
-
285-420023 Wheel Hex
$3.00
4 pcs hex nut These Nuts are part of a simple, very effective, method of joining the Axle to the Wheel with absolutely no slippage. This nut has a slot built into one side of it, and that slot fits over the Axle Pin, keeping the pin in place. This Nut will now spin with the Axle....
-
-
285-3404 CLICK AUTO - 2.4Ghz Controller
$25.00
2.4 Ghz controller for use with LiteHawk CLICK AUTO. How to sync: 1/ Make sure the model is turned OFF and locate a flat level surface.2/ Turn the CLICK AUTO ON. Place the CLICK AUTO on the flat surface, you must do this within five seconds of turning the power switch ON. 3/ Turn on the...
-
285-429089 B-Chassis Servo Saver Metal Spring
$4.00
For use with LiteHawk ACE 4x4: 1 piece metal. Servo Saver Metal Spring
-
285-429015 B-Chassis Spur Gear (62T)
$5.00
For use with LiteHawk ACE 4x4 Spur Gear (62T) With the Main Drive free, you can replace the Spur Gear. First loosen all 4 of the Grub Screws Holding it to the Center Spur Gear Shaft. When loose, give it a little twist, and gently pull the Center Drive shaft, and the Telescoping Drive shaft...
-
285-426068 RIG - Spring Compression Shocks (Set of 2)
$12.00
These Spring Compression Shocks are loaded with spring steel coil springs and a metal shaft. They're responsible for controlling compression, bounce, roll, travel and ride type. These are essential to the driving and keeping the suspension set up. These are usable for both the front and rear. The Spare Parts Baggie comes with several Shock...
-
285-481050 Axle Pin (4 pcs)
$4.00
The Axle Pins, keep the axles in the wheel knuckle bearings and create a bond between the hex nuts and the wheels so that they will turn.
-
-
285-490006-B APEX Front Fork Assembly in Blue
$6.00
Main motorcycle front section. Includes front tire and wheel, support forks and assembly section. Faring finished in Blue. LiteHawk APEX - Complete Tear DownHere's a snappy Step-By-Step Illustrated Guide to help you take apart your LiteHawk APEX motorcyle. Very useful!
-
285-490006-R APEX Front Fork Assembly in Red
$6.00
Main motorcycle front section. Includes front tire and wheel, support forks and assembly section. Faring finished in Red. LiteHawk APEX - Complete Tear DownHere's a snappy Step-By-Step Illustrated Guide to help you take apart your LiteHawk APEX motorcyle. Very useful!
-
285-429094 B-Chassis Ball Bearings 7x11x4mm (Differential)
$8.00
For use with LiteHawk ACE 4x4 Ball Bearings 7x11x4mm (Differential)
-
285-20 II Rotor Pin
$0.50
Rotor Pin for II and LITEHAWK III's Stabilizer Boom (Fly Bar)- 1 piece LITEHAWK III- Removing the Stabilizer Boom First remove the two boom connectors that attach it to the Upper Rotor Head. Now you need to press the steel pin out of the boom. Use a heavy pin or very thin nail. Press until it...
